STM32F401CC #545
Description
Good day.
I add a new board STM32F401CCU6 I have something that does not work.
boards.txt
# Black F401CUU
GenF4.menu.pnum.BLACK_F401CC=F401CUU STM32F401CUU
GenF4.menu.pnum.BLACK_F401CC.upload.maximum_size=262144
GenF4.menu.pnum.BLACK_F401CC.upload.maximum_data_size=65536
GenF4.menu.pnum.BLACK_F401CC.build.board=BLACK_F401CC
GenF4.menu.pnum.BLACK_F401CC.build.product_line=STM32F401xC
GenF4.menu.pnum.BLACK_F401CC.build.variant=BLACK_F401CC
variant.h
#ifndef _VARIANT_ARDUINO_STM32_
#define _VARIANT_ARDUINO_STM32_
#ifdef __cplusplus
extern "C" {
#endif // __cplusplus
/*----------------------------------------------------------------------------
* Pins
*----------------------------------------------------------------------------*/
#define PB9 0
#define PB8 1
#define PB7 2
#define PB6 3
#define PB5 4
#define PB4 5
#define PB3 6
#define PA15 7
#define PA12 8 // USB DP
#define PA11 9 // USB DM
#define PA10 10
#define PA9 11
#define PA8 12
#define PB15 13
#define PB14 14
#define PB13 15
#define PB12 16 // LED Blackpill
// Right side
#define PC13 17 // LED Bluepill
#define PC14 18
#define PC15 19
#define PA0 20 // A0
#define PA1 21 // A1
#define PA2 22 // A2
#define PA3 23 // A3
#define PA4 24 // A4
#define PA5 25 // A5
#define PA6 26 // A6
#define PA7 27 // A7
#define PB0 28 // A8
#define PB1 29 // A9
#define PB10 30
// Other
#define PB2 31 // BOOT1
#define PA13 32 // SWDI0
#define PA14 33 // SWCLK
// This must be a literal
#define NUM_DIGITAL_PINS 34
// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
#define NUM_ANALOG_INPUTS 5
#define NUM_ANALOG_FIRST 10
// On-board LED pin number
#define LED_BUILTIN PC13
// SPI Definitions
#define PIN_SPI_SS PA4
#define PIN_SPI_MOSI PA7
#define PIN_SPI_MISO PA6
#define PIN_SPI_SCK PA5
// I2C Definitions
#define PIN_WIRE_SDA PB7
#define PIN_WIRE_SCL PB6
// Timer Definitions
// Do not use timer used by PWM pins when possible. See PinMap_PWM.
#define TIMER_TONE TIM3
// Do not use basic timer: OC is required
#define TIMER_SERVO TIM2 //TODO: advanced-control timers don't work
// UART Definitions
#define SERIAL_UART_INSTANCE 1
// Default pin used for 'Serial' instance
// Mandatory for Firmata
#define PIN_SERIAL_RX PA10
#define PIN_SERIAL_TX PA9
/* HAL configuration */
#define HSE_VALUE 25000000U
/* Extra HAL modules */
//#define HAL_DAC_MODULE_ENABLED
//#define HAL_SD_MODULE_ENABLED
#ifdef __cplusplus
} // extern "C"
#endif
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/
#ifdef __cplusplus
// These serial port names are intended to allow libraries and architecture-neutral
// sketches to automatically default to the correct port name for a particular type
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
//
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
//
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
//
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
//
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
//
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
// pins are NOT connected to anything by default.
#define SERIAL_PORT_MONITOR Serial
#define SERIAL_PORT_HARDWARE Serial
#endif
#endif /* _VARIANT_ARDUINO_STM32_ */variant.cpp
#include "pins_arduino.h"
#ifdef __cplusplus
extern "C" {
#endif
// Pin number
const PinName digitalPin[] = {
/* USB connector on the top, MCU side */
/* Left Side */
PB_9, //D0
PB_8, //D1
PB_7, //D2
PB_6, //D3
PB_5, //D4
PB_4, //D5
PB_3, //D6
PA_15, //D7
PA_12, //D8 - USB DP
PA_11, //D9 - USB DM
PA_10, //D10
PA_9, //D11
PA_8, //D12
PB_15, //D13
PB_14, //D14
PB_13, //D15
PB_12, //D16 - LED Blackpill
/* Right side */
PC_13, //D17 - LED Bluepill
PC_14, //D18
PC_15, //D19
PA_0, //D20/A0
PA_1, //D21/A1
PA_2, //D22/A2
PA_3, //D23/A3
PA_4, //D24/A4
PA_5, //D25/A5
PA_6, //D26/A6
PA_7, //D27/A7
PB_0, //D28/A8
PB_1, //D29/A9
PB_10, //D30
PB_2, //D31 - BOOT1
PA_13, //D32 - SWDI0
PA_14, //D33 - SWCLK
};
#ifdef __cplusplus
}
#endif
// ----------------------------------------------------------------------------
#ifdef __cplusplus
extern "C" {
#endif
WEAK void SystemClock_Config(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct;
RCC_ClkInitTypeDef RCC_ClkInitStruct;
/**Configure the main internal regulator output voltage
*/
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2);
/**Initializes the CPU, AHB and APB busses clocks
*/
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLM = 25;
RCC_OscInitStruct.PLL.PLLN = 168;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
RCC_OscInitStruct.PLL.PLLQ = 4;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
_Error_Handler(__FILE__, __LINE__);
}
/**Initializes the CPU, AHB and APB busses clocks
*/
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK
| RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV2;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) {
_Error_Handler(__FILE__, __LINE__);
}
}
#ifdef __cplusplus
}
#endif